Так в вагкоме все блоки данных подписаны, что там непонятного?
ну вот например:
; VCDS Label File
;
; Copyright © 2006-2009 Ross-Tech, LLC
;
; Audi A4 (8E)
;
; Component: J220 - Engine (#01) - AMB
;
; P/N: 8E0-909-518-???
;
; includes measuring blocks, basic setting, coding, coding-ii and adaptation
;
; This file is part of a redirection package,
; make sure you have all of the following files.
;
; 8E-01.LBL
; 06B-909-518-AMB.LBL (1.8l @ 125 HP - AMB)
;
; created on 27/Jul/2006 by Sebastian Stange (
Sebastian@Ross-Tech.com)
;
; last modificationon on 03/Feb/2009
;
; requires VCDS 805.0 or newer
;
;
;---------------------------------------------------
;
; measuring blocks & basic setting
;
;---------------------------------------------------
;
;
001,0,General
001,1,Engine Speed,(G28),Specification (Idle): 700...860 RPM
001,2,Coolant,Temperature (G62),Range: -40.5...+135.0 °C\nSpecification (Warm): 80.0...115.0 °C
001,3,Lambda Control,Bank 1
001,4,Basic Setting,Requirements,see labelfile
; 1xxxxxxx - Coolant temperature above 80 °C
; x1xxxxxx - Engine speed below 2000 RPM
; xx1xxxxx - Throttle valve closed
; xxx1xxxx - Lambda regulation correct
; xxxx1xxx - State of idle
; xxxxx1xx - A/C system compressor deactivated
; xxxxxx1x - Catalytic converter over 300 °C
; xxxxxxx1 - No malfunction detected by Self-Diagnosis
;
002,0,General
002,1,Engine Speed,(G28),Specification (Idle): 700...860 RPM
002,2,Engine Load,,Specification (Idle): 13.0...45.0 %
002,3,Injection Timing,,Specification (Idle): 1.0...4.0 ms
002,4,Mass Air Flow,(G70),Specification (Idle): 2.0...4.5 g/s\nSpecififcation (Load): 90.0...100.0 g/s
;
003,0,General
003,1,Engine Speed,(G28),Specification (Idle): 700...860 RPM
003,2,Mass Air Flow,(G70),Specification (Idle): 2.0...4.5 g/s\nSpecififcation (Load): 90.0...100.0 g/s
003,3,Throttle Valve Angle
003,4,Ignition,Timing Angle
;
004,0,General
004,1,Engine Speed,(G28),Specification (Idle): 700...860 RPM
004,2,Battery Voltage,(Terminal 30),Specification: 11.0...15.0 V
004,3,Coolant,Temperature (G62),Range: -40.5...+135.0 °C\nSpecification (Warm): 80.0...115.0 °C
004,4,Intake Air,Temperature (G42),Range: -40.5...+135.0 °C\nSpecification (Warm): < +80.0 °C (max. +115.0 °C)
;
005,0,General
005,1,Engine Speed,(G28),Specification (Idle): 700...860 RPM
005,2,Engine Load,,Specification (Idle): 13.0...45.0 %
005,3,Vehicle Speed,,Range: 0.0...255.0 km/h
005,4,Load Status,,Range: Idle/Partial Throttle/Wide Open Throttle (WOT)/Enrichment/Deceleration
;
006,0,General
006,1,Engine Speed,(G28),Specification (Idle): 700...860 RPM
006,2,Engine Load,,Specification (Idle): 13.0...45.0 %
006,3,Intake Air,Temperature (G42),Range: -40.5...+135.0 °C\nSpecification (Warm): < +80.0 °C (max. +115.0 °C)
006,4,Altitude,Correction Factor
;
008,0,General (Brake System)
008,1,Brake Condition,,Range: Operated/Not Oper.
008,2,Vacuum Pump,Status,Range: Pump ON/Pump OFF
008,3,Brake Booster,Pressure
008,4,Result,,Range: Test ON/Test OFF/Sys. OK/Sys. not OK\nSpecification: Test OFF
;
B008,0,Vacuum Pump Test (Short Trip)
; Engine OFF, Ignition ON, Shift Lever: P/N
; "Activate" Basic Setting
; Firmly press Brake Pedal twice > Field 4 = Test ON
; Wait until Field 4 shows "Sys. OK"
B008,1,Brake Condition,,Range: Operated/Not Oper.
B008,2,Vacuum Pump,Status,Range: Pump ON/Pump OFF
B008,3,Brake Booster,Pressure,
B008,4,Result,,Range: Test ON/Test OFF/Sys. OK/Sys. not OK\nSpecification: Sys. OK
;
010,0,Ignition
010,1,Engine Speed,(G28),Specification (Idle): 700...860 RPM
010,2,Engine Load,,Specification (Idle): 13.0...45.0 %
010,3,Throttle Valve Angle
010,4,Ignition,Timing Angle
;
011,0,Ignition
011,1,Engine Speed,(G28),Specification (Idle): 700...860 RPM
011,2,Coolant,Temperature (G62),Range: -40.5...+135.0 °C\nSpecification (Warm): 80.0...115.0 °C
011,3,Intake Air,Temperature (G42),Range: -40.5...+135.0 °C\nSpecification (Warm): < +80.0 °C (max. +115.0 °C)
011,4,Ignition,Timing Angle
;
014,0,Ignition (Misfire Recognition - Total)
014,1,Engine Speed,(G28)
014,2,Engine Load
014,3,Misfire,(total),Specification: 0
014,4,Misfire,Recognition,Range: Disabled/Enabled
;
015,0,Ignition (Misfire Recognition - Cylinder 1-3)
015,1,Misfire Counter,Cylinder 1
015,2,Misfire Counter,Cylinder 2
015,3,Misfire Counter,Cylinder 3
015,4,Misfire,Recognition,Range: Disabled/Enabled
;
016,0,Ignition (Misfire Recognition - Cylinder 4)
016,1,Misfire Counter,Cylinder 4
016,4,Misfire,Recognition,Range: Disabled/Enabled
;
018,0,RPM/Load Barriers
018,1,Lower,RPM Barrier
018,2,Upper,RPM Barrier
018,3,Lower,Load Barrier
018,4,Upper,Load Barrier
;
020,0,Ignition (Timing Retardation Cylinder 1-4)
020,1,Timing Retardation,Cylinder 1
020,2,Timing Retardation,Cylinder 2
020,3,Timing Retardation,Cylinder 3
020,4,Timing Retardation,Cylinder 4
;
022,0,Ignition (Timing Retardation Cylinder 1 && 2)
022,1,Engine Speed,(G28)
022,2,Engine Load
022,3,Timing Retardation,Cylinder 1
022,4,Timing Retardation,Cylinder 2
;
023,0,Ignition (Timing Retardation Cylinder 3 && 4)
023,1,Engine Speed,(G28)
023,2,Engine Load
023,3,Timing Retardation,Cylinder 3
023,4,Timing Retardation,Cylinder 4
;
026,0,Ignition (Knock Control Cylinder 1-4)
026,1,Voltage,Cylinder 1
026,2,Voltage,Cylinder 2
026,3,Voltage,Cylinder 3
026,4,Voltage,Cylinder 4
;
028,0,Ignition (Knock Sensor Test)
028,1,Engine Speed,(G28)
028,2,Engine Load
028,3,Coolant,Temperature (G62),Range: -40.5...+135.0 °C\nSpecification (Warm): 80.0...115.0 °C
028,4,Result,,Range: Test ON/Test OFF/Sys. OK/Sys. not OK\nSpecification: Sys. OK
;
B028,0,Ignition (Knock Sensor Test - Short Trip)
; "Activate" Basic Setting
; Firmly press Brake Pedal and Throttle Pedal at once
; Engine Speed increases to 2200 RPM automatically > Field 4 = Test ON
; Wait until Field 4 shows "Sys. OK"
B028,1,Engine Speed,(G28)
B028,2,Engine Load
B028,3,Coolant,Temperature (G62),Range: -40.5...+135.0 °C\nSpecification (Warm): 80.0...115.0 °C
B028,4,Result,,Range: Test ON/Test OFF/Sys. OK/Sys. not OK\nSpecification: Sys. OK
;
030,0,Lambda Control (Sensor Status)
030,1,Bank 1,Sensor 1
; 1xxxx - Lambda Sensor Control Cyl. 1 active
; x1xxx - Catalytic Converter Venting active
; xx1xx - Lambda Sensor Heating on
; xxx1x - Lambda Sensor ready
; xxxx1 - Lambda Control active
030,2,Bank 1,Sensor 2
; 1xxx - Lambda Control (P-Portion) active
; x1xx - Lambda Sensor Heating on
; xx1x - Lambda Sensor ready
; xxx1 - Lambda Control (I-Portion) active
;
031,0,Lambda Control
031,1,Lambda Control,Bank 1 (actual)
031,2,Lambda Control,Bank 1 (specified)
;
032,0,Lambda Control (Mixture Adaptation)
032,1,Adaptation (Idle),Bank 1 Sensor 1
032,2,Adaptation (Partial),Bank 1 Sensor 1
Ну и так далее....
